Two Thunderbolt 4, two 5Gbps USB-A, HDMI 2.0b, headphonesĨ.76×12.43×0.6 inches (222.5×315.6×15.36 mm)ĭell's XPS 13 has been the pace car for the Windows side of the thin-and-light laptop race for years now, ever since it adopted the now-ubiquitous ultra-thin display bezel back in 2015. Intel Core i7-1260P (4 P-cores, 8 E-cores) Video for USB 3 Docking Stations currently is not supported, so you must use a USB Port Replicator with Digital Video (USB 2.Andrew Cunningham reader comments 118 with Specs at a glance: Lenovo ThinkPad X1 Carbon Gen 10ġ4.0-inch 1920×1200 touchscreen (162 PPI) The slackware wiki describes one way to do this. You need to manually install the proprietary firmware. Kernel: Bluetooth: hci0: BCM: Patch brcm/BCM20702A1-0a5c-21e6.hcd not found Kernel: bluetooth hci0: Direct firmware load for brcm/BCM20702A1-0a5c-21e6.hcd failed with error -2 $ lsusb 0bdb:1926 Ericsson Business Mobile Networks BV Keyboard backlightįirst try to set up Bluetooth normally. $ lsusb 0bdb:1926 Ericsson Business Mobile Networks BV GPS Tested OK with NetworkManager with modemmanager installed etc/modprobe.d/nf options cdc_ncm prefer_mbim=N The SIM-card must be inserted in the back of the laptop.Īdd text to the following file and reboot This model includes a Ericsson H5321gw adapter that can be used as a mobile broadband adapter and GPS. $ lsusb 147e:2020 Upek TouchChip Fingerprint Coprocessor (WBF advanced mode) WWAN (Mobile broadband) See fingerprint-gui for more information about config To get the gui's dropdown to recognize your device, you will have to add your user to the plugdev group: Tested with guvcviewįor a GUI, fingerprint-gui AUR is already patched to work with the X1's newer fingerprint reader. Xrandr -output DP1 -mode 1920x1200_60 KMSĮnable KMS using the i915 module and by enabling VT in BIOS. The correct mode can be added per xrandr#Adding undetected resolutions: This does not occur if the external screen is connected after booting. MiniDP to VGA), there is a bug getting EDID for the external screen while booting: Consider using the #Xbindkeys approach instead. Note that the ACPI backlight is disabled by default on Windows 8 hardware with a native backlight. In order to use them properly you need to add the kernel parameter acpi_osi="!Windows 2012". Writing custom ACPI handlers for the brightness adjustment keys seems to have no effect. Install xbindkeys and append the following to ~/.xbindkeysrc: To work around this add the kernel parameter video.brightness_switch_enabled=0. gnome-settings-daemon) along with the internal graphics module changing the brightness when brightness adjustment keys are pressed causing multiple steps per press. Some desktop environments may lack granularity while changing brightness. Use either the #Xbindkeys_2 or #ACPI methods to fix this. See intel for more info.ĭefault brightness adjustment keys work but need to be pressed multiple times to increase/decrease the screen brightness. The video card installed is Intel HD Graphics 4000. $ lspci Network controller: Intel Corporation Centrino Advanced-N 6205 (rev 96) Touchscreen Wireless works out of the box using the iwlwifi module. Wired networking works out of the box with the Ethernet to USB adapter. To work around it, add intel_pstate=no_hwp to your kernel parameters.įor alternative window managers (Fluxbox, etc.), try installing xbindkeys and adding the following to ~/.xbindkeysrc: This is due to a bug introduced in Linux 4.4. Then simply follow the normal installation guide. Booting Legacy-BIOSīoot into your BIOS and change the boot mode to Legacy. For more recent generations, see Category:Lenovo. Note: This article is about the 1st generation model introduced in 2012.
0 Comments
Leave a Reply. |